Land Pride RCM4015
Double tap to zoom
|All Land Pride Rotary Cutters have been designed and tested and meet rigorous
voluntary testing procedures according to ISO 4254.
|Factory assembled||Arrives for quick and easy set-up. Minimal time is wasted setting or prepping the unit.|
|7 Year gearbox warranty*||Shows confidence in gearbox integrity. (6th & 7th year parts only)|
|Rugged heavy built gearboxes||Capable of handling heavy cutting applications.|
|Gearbox seal protection||Gearbox bottom seal protection for longer bearing life.|
|2 Piece shield on wing gearboxes||Driveline grease zerks are easier to access.|
|LP Performance self-leveling hitch||Reduces drawbar wear by keeping hitch level while going through ditches.|
|Low hitch weight on tractor tongue||Ideal for smaller hp tractors by reducing the amount of weight on the drawbar|
|Narrow A-frame hitch||Allows for a tighter turning radius.|
|Adjustable park jack angle||Park jack can be adjusted to be perpendicular to the ground.|
|Adjustable driveline hanger||Serves as a support rest for the driveline when the cutter is unhooked from the tractor. Assist operator when attaching driveline to tractor power take-off shaft.|
Cat. 6 CV or Cat. 5 Conventional
|Driveline is matched just right for capacity of tractor. Constant velocity (CV) U-joint
allows for 80 degree turns without doing damage to the driveline.
|Cat. 5 intermediate & Cat. 4 wing
drivelines with slip-clutches
|Driveline is sized right for the intended cutting capacity. Slip-clutch will slip under load
instead of twisting the driveline.
|Grease zerks on end caps of
driveline cross journals
|Intermediate and wing driveline cross journals are easier to grease.|
|High blade tip speed (See
Specifications for actual FPM)
|Allows clean cutting of material.|
|6" Blade overlap||Eliminates skipping during turns.|
|Left wing rotates clockwise||Better discharge of material. Picks up tractor tracks.|
|3/16" Round stump jumper||Standard thick stump jumper material keeps damage to a minimum.|
|Smooth top design||Reduces accumulation of debris and is easier and faster to clean.|
|Deck sheet tops are 100% welded||Makes center decks and wing decks stronger.|
|1/4" Sidewall thickness||Increased thickness reduces damage from objects being thrown into deck sidewalls.|
|Beveled skid shoes on wings||Reduces gouging the ground when turning.|
|Hinged wing sections||Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches and
hollows can cause uneven cutting.
|1" Solid hinge rods||Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in
the hinge area itself.
|Wing transport locks||Wing transport locks securely hold the wings in the folded position in case of hydraulic
|Enclosed front to rear dual
|Dual leveling rods enable the cutter to pull equally on the rear axle during travel over
|5-Bolt hubs||5-Bolt hubs makes the wheel assembly more durable and longer lasting.|
|Spring cushioned center-axle||Protects unit from bumps and ground shock.|
|Replaceable wheel spindles||Wheel spindles can be replaced when damaged without replacing entire axle
|LED Signal lights||LED lights are bright, long lasting, and resistant to vibration, unlike incandescent
|Wheel options||Laminated tires: Eliminates flats.
Airplane tires without foam filling: Give better cushion while transporting.
Airplane tires with foam filling: Give better cushion while transporting and can’t go
|LP Performance hitch option||Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and
pivots about the tractor drawbar.
|Double swivel hitch option||Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and
pivots about the tractor drawbar.
|Bar-tite hitch option||Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.|
|Deck ring option||Keeps blades from damaging the deck.|
|Specifications & Capacities||RC4015 & RCM4015|
|Horsepower range||50 - 200|
|Gearbox Horsepower||540 rpm or 1000 rpm
250 hp Divider
210 hp Center & Wings
|210 hp Center & Wings|
|Gearbox lubrication||Gear Lube 80-90W EP|
|Gearbox oil capacity||Splitter: 3.5 pints; Center deck & Wings: 6 pints|
|Cutting capacity||3 1/2"|
|Blade tip speed
At 540 rpm
At 1000 rpm
Center blades = 16,300 FPM Wing blades = 16,300 FPM
Center blades = 16,300 FPM Wing blades = 16,000 FPM
|Hitch types||Standard Clevis, LP Performance Hitch, Bar-Tite Hitch, Ball Hitch, or Pintle Hitch|
|Hitch jack||Standard (7,000 lbs.)|
7 Pin connector
SAE J5560 pin configuration
Minimum transport width
|Overall length||15'-6" (With center deck raised fully up)|
|Cutting Height||2" - 14"|
|Lift hydraulics||3" x 8" hydraulic cylinder, hoses, fittings & stroke control spacers|
|Wing hydraulics||2 1/2" x 12" hydraulic cylinders, hoses & fittings|
|Wing Transport protection||Wing Transport Locks|
|Deck material thickness||10 Gauge|
|Side skirt thickness||1/4" Steel|
AR400 1 Replaceable skid shoe per wing
AR400 2 Replaceable skid shoes
|Blades - 6 (2 per carrier)||1/2" x 4" Heat Treated
Free Swinging Alloy Steel with Uplift
|Blade bolt||Keyed with hardened flat washer & locknut|
|Stump jumper / blade holder||3/16" Thick round dish shaped pan, reinforced with 1" x 4" blade bar|
|Front & rear guards||Optional rubber, single row chain, or dual row chain|
|Input driveline 540 & 1000 rpm||Cat. 6 with constant velocity u-joint or Cat. 5 with conventional (non-cv) u-joint|
|Intermediate driveline||Standard - Category 4 with Slip-Clutch|
|Wing drivelines||Standard - Category 4 with Slip-Clutch|
|Tire options||6" x 21" Laminated tires, 25.5" new foam filled tires,
29" x 16 ply used aircraft tires without foam filling.
|Number of wheels||4 - Wheels: Two on transport axle and one on each wing axle
6 - Wheel option: Four on transport axle and one on each wing axle.
8 - Wheel option: Four on transport axle and two on each wing axle.
|Transport axle||Spring-cushioned on center transport axle|
|Hubs||Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" shafts.|