Land Pride RCBM6615
Features
Features | Benefits |
Surpassed rugged industry standards | All Land Pride Cutters have been designed and tested to meet rigorous voluntary testing procedures according to ISO 4254-13. |
Factory assembled | Saves customer set-up time and money. Adjustments should always be made by dealer. |
7 Year gearbox warranty | Shows confidence in gearbox integrity. (Years 6 & 7, parts only.) |
Rugged heavy built gearboxes | Gearboxes are capable of handling heavy cutting applications. |
Gearbox seal protection | Gearbox bottom seal protection for longer bearing life. |
2 3/8" Output gearbox shaft | Large output shaft handles shock loads better. |
2 Piece shield on wing gearboxes | Driveline grease zerks are easier to access. |
Self-leveling hitches | Reduces drawbar wear by keeping hitch level while going through ditches. |
Narrow A-frame hitch | Allows for a tighter turning radius. |
Adjustable park jack angle | Park jack can be adjusted to be perpendicular to the ground. |
Adjustable driveline hanger | Serves as a support rest for the driveline when the cutter is unhooked from the tractor. Assist operator when attaching driveline to tractor power take-off shaft. |
Input Driveline: Cat. 6 CV or Cat. 5 conventional | Holds up to shock loads and harsh mowing conditions. Constant velocity (CV) U-joint allows for 80 degrees turns without doing damage to the driveline. |
Grease zerks on end caps of driveline cross journals | Intermediate and wing driveline cross journals are easier to grease. All drivelines have access holes for greasing the U-joints and inner profiles. |
4 Plate slip-clutch | Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline when imparcts are encountered |
High blade tip speed | Allows clean cutting of material and even distribution. See Specifications for actual FPM. |
6" Blade overlap | Eliminates skipping during turns. |
High cutting capacity | Can cut brushy areas with saplings up to 4 1/2". |
Pre-cut chamber | Allows grass and vegetation to stand back up prior to cutting for a more complete cut. |
Reinforced leading edge | Front of deck can withstand heavy brush and saplings. |
12" Deck height | Handles heavy cutting, which reduces balling-up of cut material under the deck. |
10 Gauge smooth deck top | Reduces accumulation of debris and is easier and faster to clean. |
7 Gauge smooth deck bottom | Heavy deck design holds up to harsh conditions. No bottom obstructions. |
Replaceable 1/4" side skirt | Reduces debris piercing possibilities. Can be replaced if damaged. |
Left wing rotates clockwise | Better discharge of material. Picks up tractor tracks. |
3/16" Round stump jumper backed with a 1" thick mounting plate. | Heavy round stump jumper for protecting the gearbox seal and gearbox output shaft. Can hold up to tough conditions. |
Spindle nut protected | Spindle nut and threads extending beyond the nut are guarded to protect against damage from hitting solid objects. |
Beveled skid shoes on wings | Reduces gouging the ground when turning. |
LED Signal lights | LED lights are bright, long lasting, and resistant to vibration, unlike incandescent counterparts. |
Hinged wing sections | Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting. |
Greasable wing folding hinges | Provides for a long hinge life and allows wings to fold up and down with less stress. |
1" Solid hinge rods | Gives greater strength to the cutter from front to rear, and in the hinge area itself. |
Wing transport locks | Holds transport wings in the folded-up position in case of hydraulic pressure loss. |
Collapsible 1" Leveling rods | Prevents damage and failure to leveling rods. Large diameter leveling rods provide superior supporting strength over rough terrain. |
Enclosed dual leveling rods | Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain. Many competitors only use one leveling rod. |
5-Bolt hubs | 5-Bolt hubs makes the wheel assembly more durable and longer lasting |
Specifications
Specifications & Capacities | RCB6615 & RCBM6615 Series 2 |
Horsepower range | 50 to 250 |
Gearbox horsepower | 250 hp splitter 210 hp center & wing |
Gearbox oil capacity | 5.5 Pints: divider gearbox 10 Pints: center deck, LH deck & RH deck spindle gearboxes |
Gearbox lubrication | Gear lube 80-90W EP |
Cutting capacity | 4 1/2" |
Machine weight Tongue weight Total weight |
Chain guards, 6 AC tires, and standard clevis 1,842 lbs. 5,738 lbs. |
Blade tip speed At 540 rpm At 1000 rpm |
Center blades = 16,300 FPM Wing blades = 16,300 FPM Center blades = 16,300 FPM Wing blades = 16,000 FPM |
Tongue types | Optional Self-Leveling Clevis Hitch, LP Performance Hitch, Bar-Tite Hitch, Pintle Hitch, or Ball Hitch |
Hitch jack | Standard (7,000 lbs.) |
Signal lights 7 Pin connector |
LED (light-emitting diode) SAE J560 pin configuration |
Cutting width Overall width Minimum transport width |
15' - 0" 15' - 8 1/2" 7' - 5 1/4" (With tandem wheels & cutting height at 2") |
Overall length | 17' - 0 1/2" (With tandem wheels & cutting height at 2") |
Deck height | 12" |
Cutting height | 2" to 14" |
Lift hydraulics Center deck Right wing Left wing | 3 1/2" x 8" Re-phasing hydraulic cylinder with hoses, fittings & stroke control spacers 3 1/4" x 8" Re-phasing hydraulic cylinder with hoses & fittings 3" x 8" Re-phasing hydraulic cylinder with hoses & fittings |
Wing hydraulics | Two independently plumbed 3 1/2" x 8" dual-acting cylinders complete with hoses & fittings |
Wing transport protection | Transport locks with hitch pins |
Deck material | 10 Gauge top deck and 7 gauge bottom deck |
Side skirt material | Bolt-on replaceable 1/4" steel |
Skid shoes Wing deck Center deck | Reversible & Replaceable: 2 straight skid shoes and 2 AR400 leading skid shoes. Replaceable: 2 skid shoes |
Six blades (2 per carrier) | 1/2" x 4" Heat treated free swinging alloy steel with up lift |
Blade overlap | 6" |
Blade bolt | Keyed with hardened flat washer & locknut |
Stump jumper / blade holder | 3/16" Thick round dish shaped pan, reinforced with 1" thick blade mounting plate; or optional Shredder Kit |
Deck ring | Optional 1/2" x 3" fully welded |
Front & rear guards | Optional rubber, single chain, double chain, or double chain with cable |
Input driveline 540 & 1000 rpm | Cat. 6 with constant velocity u-joint or Cat. 5 with conventional (non-cv) u-joint |
Intermediate & wing drivelines | Cat. 5 with slip-clutch |
Wheel options Standard axle & tandem axle |
6" x 21" Laminated tires, 25.5" new tire with or without foam fill, 24" x 12 ply used pneumatic aircraft tires, and 29" x16 ply used pneumatic aircraft tires. |
Number of wheels Standard axle |
6 - Wheel option: 4 on transport axle and one on each wing axle 8 - Wheel option: 4 on transport axle and two on each wing axle |
Tandem axle | 6 - Wheel option: 4 on transport axle and one non tandem on each wing axle 8 - Wheel option: 4 on transport axle and two on each wing axle |
Standard transport axle | Spring-cushioned on trailing arms |
Hubs | Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" shafts |